COVID-19 – Важне информације о наставку пословања ИСС-а током ванредног стања
Да ли су вам стандарди потребни у вашем послу?
Да
Не
Понекад
Не знам
Укупан број гласова: 7538

Пријавите се!
 


naSRPS EN 61010-031:2015/prAA:2020

Фаза: 40.20 - Почетак јавне расправе о нацрту српског стандарда
Почетак: 2020-03-13
Крај: 2020-05-12

Веза са међународним стандардима
Ovaj standard je identičan sa: EN 61010-031:2015/prAA CLC/TC 66X

Наслов на српском језику

Zahtevi za bezbednost električnih uređaja i opreme za merenje, upravljanje i laboratorijsko korišćenje — Deo 031: Zahtevi za bezbednost sklopova ručnih sondi za električna merenja i ispitivanja – Izmena 11

Наслов на енглеском језику

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test

Апстракт на српском језику

Ovaj deo standarda se odnosi na bezbednost sklopova ručnih sondi koji se drže u ruci i sklopova sondi kojima se ručno manipuliše. Ovi sklopovi sondi su predviđeni da se koriste kao interfejs između električne pojave i mernog instrumenta ili instrumenta za ispitivanje.

Апстракт на енглеском језику

1.1.1 Probe assemblies included in scope This part of IEC 61010 specifies safety requirements for hand-held and hand-manipulated probe assemblies of the types described below, and their related accessories. These probe assemblies are for direct electrical connection between a part and electrical test and measurement equipment. They may be fixed to the equipment or be detachable accessories for the equipment. a) Type A: low-voltage and high-voltage, non-attenuating probe assemblies. Non-attenuating probe assemblies that are RATED for direct connection to voltages exceeding 30 V r.m.s., 42,4 V peak, or 60 V d.c., but not exceeding 63 kV. They do not incorporate components which are intended to provide a voltage divider function or a signal conditioning function, but they may contain non-attenuating components such as fuses (see Figure 1). b) Type B: high-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies that are RATED for direct connection to secondary voltages exceeding 1 kV r.m.s or 1,5 kV d.c. but not exceeding 63 kV r.m.s or d.c. The divider function may be carried out wholly within the probe assembely, or partly within the test or measurement equipment to be used with the probe assembly (see Figure 2). c) Type C: low-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies for direct connection to voltages not exceeding 1 kV r.m.s. or 1,5 kV d.c. The signal conditioning function may be carried out wholly within the probe assembly, or partly within the test or measurement equipment intended to be used with the probe assembly (see Figure 3). d) Type D: low-voltage attenuating, non-attenuating or other signal conditioning probe assemblies, that are RATED for direct connection only to voltages not exceeding 30 V r.m.s., or 42,4 V peak, or 60 V d.c., and are suitable for currents exceeding 8 A (see Figure 4). 1.1.2 Probe assemblies excluded from scope This standard does not apply to current sensors within the scope of IEC 61010-2-032 (hand-held and hand-manipulated current sensors), but may apply to their input measuring circuit leads and accessories.

Комисија за стандарде


ICS



Директиве