COVID-19 – Важне информације о наставку пословања ИСС-а током ванредног стања
Да ли су вам стандарди потребни у вашем послу?
Не знам
Укупан број гласова: 7535

Пријавите се!

SRPS CEN/TS 14807:2010

Статус: Повучен
Језик: Engleski
Бр. страна: 12
Датум: 27.08.2010.
Датум повлачења: 28.11.2014 .
Службени гласник: 65/10
Број решења:
Издање: 1 ED
Веза са међународним стандардима
Ovaj standard je identičan sa:
CEN/TS 14807:2004   CEN/TC 155
Цена: 1755 RSD

За читање онлајн


Наслов на српском језику

Sistemi cevovoda od plastičnih masa — Termoreaktivne plastične mase ojačane staklom (GRP) na bazi nezasićenih poliestarskih smola (UP) — Uputstvo za strukturnu analizu podzemnih GRP-UP cevovoda

Наслов на енглеском језику

Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines

Апстракт на српском језику

Ovaj dokument koji predstavlja uputstvo za strukturnu analizu podzemnih instalacija obuhvata granične vrednosti koje se mogu primeniti na cevi od termoreaktivne plastične mase ojačane staklom (GRP) za transport tečnosti pod pritiskom ili u gravitacionim uslovima. Ovim dokumentom se ne utvrđuje poseban postupak strukturne analize, već se daje uputstvo za izbor postupka strukturne analize.

Апстракт на енглеском језику

This document, which is a guidance document for use with a structural analysis procedure for below ground installations, covers limits applicable to glass-reinforced thermosetting plastics (GRP) pipes used for the conveyance of liquids under pressure or gravity conditions. This document does not specify a particular structural analysis procedure but gives guidance on the selection of a structural analysis procedure. It concludes that any established structural analysis procedure may be used provided it includes the assessment of short and long-term deflection and buckling resistance. NOTE 1 Products complying to the applicable system standards (prEN 1796 [1] or prEN 14364 [2]), which are not subject to internal pressure, are suitable as long as the analysis shows that the long-term deflection of the installed pipes is limited to 6 %, which is the basic assumption of the system standards. Similarly products complying with the applicable system standards (prEN 1796 [1] or prEN 14364 [2]), which are subject to internal pressure, are suitable as long as the analysis shows that the initial and long-term deflection of the installed pipes does not exceed 3 %. NOTE 2 The approach followed when preparing a structural analysis procedure in general does not depend on the nominal size(s) of the pipe(s). NOTE 3 A suitable structural analysis procedure would normally be capable of being used for pipes operating at different temperatures provided that the corresponding temperature re-rating factors for the relevant pipe properties are applied, as specified in the referring standard(s). Nevertheless, high service temperatures may require an additional analysis of the longitudinal stresses and strains and/or a special design of the joints. NOTE 4 Normal structural analysis procedures are intended to cover normal soil installation conditions. Pipes to be designed for installations in abnormal or unusual conditions, e.g. in quick soils or a marine sea-bed, may require special

Комисија за стандарде



Нема информација.

Национални пропис

Нема информација.

Национална активност


analiza, klasifikacija, oznake, plastične mase ojačane staklom, matematička izračunavanja, sistem cevovoda, cevi od plastičnih masa, poliestarske smole, cevi pod pritiskom, specifikacije, statičko opterećenje, termoreaktivni polimeri