SRPS ENV 1046:2008
Статус: Повучен
Језик: Engleski Бр. страна: 64 Датум: 28.07.2008. Датум повлачења: 28.11.2014 . Службени гласник: 75/08 Број решења: Издање: 1 ED |
Веза са међународним стандардима
Ovaj standard je identičan sa:
ENV 1046:2001 CEN/TC 155 |
Цена: 4278 RSD За читање онлајн ![]() ![]() |
Наслов на српском језику
Sistemi cevovoda i kanala od plastičnih masa - Sistem za transport vode ili otpadne vode (kanalizacije) izvan građevinske konstrukcije - Postupci za nadzemnu i podzemnu instalaciju
Наслов на енглеском језику
Plastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for installation above and below ground
Апстракт на српском језику
Ovaj predstandard primenjuje se za nadzemnu i podzemnu ugradnju/polaganje sistema cevovoda od plastičnih masa koji se koriste za transport vode ili kanalizacije pod dejstvom gravitacione sile i pritiska. Namenjen je za primenu za cevi sa nazivnim merama do DN 3000.
U ovom predstandardu termin cev obuhvata i fitinge, pomoćne proizvode i komponente.
Апстракт на енглеском језику
This prestandard is applicable to the installation of plastics piping systems to be used for the conveyance of water or sewage under gravity and pressure conditions above and below ground. It is intended to be used for pipes of nominal size up to and including DN 3000.
Where in this prestandard the term "pipe" is used then it serves also to cover any "fittings", "ancillary" products and "components".
NOTE 1 It is assumed that additional recommendations and/or requirements are detailed in the individual materials System Standards. Instances where this is expected to apply include those indicated in this prestandard as follows:
a) any special transportation requirements (see 4.2.6);
b) maximum storage height (see 4.4.3 and 4.4.4);
c) maximum storage period in direct sunlight (see 4.4.6);
d) any climatic conditions requiring special storage (see 4.4.7);
e) limiting initial and/or long-term deflections (see 5.1.1 and 5.1.2);
f) information on mole ploughing and boring (see and 5.2), if applicable;
g) longitudinal tensile modulus and strength (see 5.3.1.2);
h) coefficient of thermal linear expansion (see 5.3.2.2 and Annex B);
i) suitability for use in areas exposed to sunlight (see 5.3.3);
j) selection of appropriate jointing system (see clause 6);
k) recommended radii of curvature for cold bending (see 7.1);
l) permitted rates of loss of water under test (see 8.2.1);
m) if applicable the relationship between SDR and stiffness.
NOTE 2 Guidance and instructions concerning commissioning of systems can be found in the standards prepared by CEN/TC 164 and by CEN/TC 165 and the relevant national and/or local regulations.
NOTE 3 Concerning the character of this document see Foreword and Introduction.
Комисија за стандарде
ICS
Директиве
Нема информација.Национални пропис
Нема информација.Национална активност
SRPS CEN/TR 1046:2014
zamenjuje
SRPS ENV 1046:2008
- 28.11.2014
Дескриптори
cevovodi;cevi od plastičnih masa;plastične tube;fitinzi;kanalizacione cevi;prenos vode; polaganje;definicije;instalacija